Semi-Automatic Double-Station Rotary Pipe End Forming Copper Processing

We meet our customers' needs by offering specific sections of our 200T High speed Hydraulic Press, Four column Hydraulic Press With Movable Worktable, 20T Single Column Hydraulic Press to maximize customer loyalty. We provide good service, enhance the added value of products, excavate the expected and added value of products, and reduce the total customer cost on the basis of increasing the total customer value. By decomposing and implementing responsibilities at all levels, we make the overall operation of the enterprise more standardized. We hope we can establish long-term cooperation with all of the customers. Corporate culture is the core value of the enterprise which is generally recognized and shared by all employees.

YH32 special press bolt machine

Features:

1. The fuselage adopts a three-beam and four-column structure. The upper beam and the worktable are combined into a fixed frame through the column, fastening nut and adjusting nut. The accuracy of the frame is adjusted by the adjusting nut, which has good strength, rigidity and accuracy retention.

2. Large parts such as upper beams, workbenches, and sliding blocks are welded parts of steel plates. After computerized design, their strength, rigidity, structure, anti-deformation, etc. all meet the standards and requirements for use, and have a sufficient safety factor; carbon dioxide is used Gas shielded welding and manual arc welding, the welding quality meets the requirements, and the deformation stress is eliminated through aging vibration treatment.

3. Slide block: steel plate welded parts with box-shaped structure. The guide sleeve at the four-pillar guide hole is made of nano-molecular composite material, which has good resistance and precision retention. There is a T-shaped groove on the lower plane of the slider for installing the mold.

4. Upper beam: steel plate welded parts of box-shaped structure, with main working oil cylinder inside, and liquid-filled oil tank on it.

5. Workbench: Steel welded structural parts, which are connected to the upper beam and sliding block to form the main machine through the column.

6. Cylinder: It adopts a five-cylinder design, is arranged in the upper beam hole, and is sealed with double imported sealing rings. The guiding part is treated with welded copper, which is well sealed and has strong wear resistance. The material of the cylinder body is No. 45 forged steel, and the forging is 3 Grade (GB/13315-1991) forgings have passed the ultrasonic flaw detection and the hardness of quenching and tempering treatment is qualified.

7. There is an ejector device under the workbench, which is mainly used for ejection and material return processes, and can also be used for the forming process of reverse-stretched parts.

8. Column: The material is 45# forged steel, after quenching and tempering, the surface is plated with hard chromium to increase the wear resistance and the hardness is qualified.

9. The nut material is 45# forged steel, which matches the thread on the column to lock the body.

10. Limit device: Located on the right side of the main body, the travel switch controls the upper and lower limit positions. Adjusting the upper and lower limit switches means adjusting the up and down movement position of the slider.

Product parameters:

Applicable fields (part of tooling required to be purchased):

● Press-fit large transmission gears and shafts

● Correcting the front axle

● Correcting deformed workpieces

● Disassembly and assembly of cylindrical cone bearings

● Replace the diaphragm spring of the automobile clutch

● Press-fit the bearing outer ring of the bearing

● Replace the reaction rod rubber assembly

● Disassembly and assembly of various tight-fitting parts

● Change the clutch plate stop pin buffer spring

● Riveting, cutting, and casting rear axle basin tooth rivets

● There are various pin sleeves for press-fitting piston pins and steering knuckle main pins

Common problem:

Are you a manufacturer?

Yes, the company has a variety of high-precision production equipment and inspection equipment, a complete production team, many years of production experience, to meet your ordering needs, specializing in the production of single-column hydraulic press, four-column hydraulic press, powder forming hydraulic press, stretch forming hydraulic press, various A variety of auto parts presses, machines that can process metal, plastic, rubber, wood, powder and other products.

How to install the machine?

To provide customers with a full range of technical support, we can also send technicians abroad to install and train for our customers.

How about after-sales?

The company provides 24-hour after-sales service, after-sales service mailbox: huntermachinery@gamil.com

Since the Semi-Automatic Double-Station Rotary Pipe End Forming Copper Processing has been put into production, through continuous innovation and development, its product functions have become more complete. We advocate the professional ethics of "pragmatic and dedicated, faithful to duty" and carry forward the team spirit of "sincere unity and cooperation". We will constantly welcome guests from all over the world to our firm.